9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.?/DIV>
牋牋?9
4.燗dvanced燦etworking
4.1. Addressing
XCite radio modems utilize three layers of addressing to communicate between radio modems.
The network layers are depicted below. Only radio modems with the matching addresses are able
to communicate. The main layers of XCite Networking and Addressing are:
" Vendor Identification Number (ATID)
" Channel (ATHP)
" Destination Address (ATDT)
Figure?01. Addressing爈ayers燾ontained爄n爐he燫F爌acket爃eader
Each network layer provides a separate layer of filtration. The Vendor Identification Number (VID)
provides the first layer of filtration through the ID (Modem ID) Parameter. If the incoming RF data
carries a matching VID number, the data continues through to the subsequent Channel and Desti-
nation Address layers. The Destination Address is the last network layer and provides the most
granular form of filtration. If at any point during the incoming RF data flow the numbers in ques-
tion do not match, the data is discarded.
XCite Modules and RF Modems are built around a peer-to-peer protocol that inherently supports a
multidrop type network (similar to RS-485). In their default state, any XCite radio modem will
communicate with any other XCite radio modem in its default state.
4.1.1. Vendor Identification Number (ATID)
The bottom half of the ID (Vendor Identification Number) Parameter range is user-settable. The
upper half of the range is factory-set and read-only. The value of the ID Command is called the
Vendor Identification Number (VID). A unique VID is available upon special request. The VID is
programmed to the XCite Module at the factory and is stored in the modem's permanent memory.
Only modems with matching VIDs can communicate with each other.
VID addressing ensures that radio modems ignore transmissions and receptions of XCite Radio
Modems having a different VID in the same vicinity. To request a unique VID, contact MaxStream
to obtain the VID Request Form.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ZMN2400HPDB
BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B
KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC
IC TEMP SENSOR NI1000 SOT23-3
02110102-000
SNSR TILT RATIO 60DEG 500MA FLNG
1-5209285-2
FOPC BOA 12DB FC/UPC BP SM
2-1693560-0
BOA 20DB LC/UPC BB
517SS16
MAGNETIC SENSORS BIPOLAR ICS
5209597-9
BOA 9DB DW SC/APC
相关代理商/技术参数
XIB-U
功能描述:界面模块 USB interface board 24XStream 9XCite
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
XIC25040
制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-080
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-081
功能描述:电源管理IC开发工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-082
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-083
功能描述:电源管理IC开发工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XIM15120-G-C2E
制造商:Thomas & Betts 功能描述:INCANDESCENT